ARCTIC CAT ADAPT DRIVE CLUTCH 8in 33mm Cyles and Sleds

New for model year 2022, Arctic Cat ADAPT Drive Clutch
8-inch diameter and 33mm taper with idler bearing
1-pound lighter than 2021 production TEAM clutch
5% reduction in inertia
Compact design with 25mm or 14.1% reduction in width
When installing a new clutch, it is recommended to replace the drive belt or premature belt failure could occur
Note: As an alternative to the 2623-325 Drive Clutch Spacer, you can also use the shorter 2623-308 Drive Clutch Bolt with the original 1623-649 washer
Requires the 0744-080 blue puller to remove this clutch (Sold separately)
Requires the 8639-454 cam arm pin kit (Sold separately)
Does NOT include cam arm weights, pins, screws, or washers and will need them added for specific model and altitude calibration
Includes clutch with (1646-009) 85/225-pound spring installed

Replaces Part # 0746-881

Direct replacement for the following models:

2022-2023 M 8000
2022-2023 Norseman 8000
2022-2023 Riot 6000, 8000
2022-2023 ZR 6000, 8000

Can be used to replace the 0746-862, 0746-869, & 0746-881 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer, remove adjuster in driven, install 2623-325 drive clutch spacer, and install 0627-107 belt. (Sold separately)

2016-2017 M 6000
2016-2017 XF 6000
2016-2017 ZR 6000

Can be used to replace the 0746-862, 0746-869, & 0746-881 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer, remove adjuster in driven, install 2623-325 drive clutch spacer, and install 0627-111 belt. (Sold separately)

2016-2017 M 8000
2016-2017 XF 8000
2016-2017 ZR 8000

Can be used to replace the 0746-885 & 0746-888 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer and install 2623-325 drive clutch spacer. (Sold separately)

2018-2019 M 6000 & 8000
2018-2019 Norseman 6000 & 8000
2018-2019 Pantera 6000
2018-2019 XF 6000 & 8000
2018-2019 ZR 6000 & 8000
2018-2021 ZR 6000 R XC

Can be used to replace the 0746-895 TEAM clutch that came stock on the following models.
You will need to remove drive clutch washer and install 2623-325 drive clutch spacer. (Sold separately)

2020-2021 M 6000 & 8000
2022 M 8000 Early Build
2020-2021 Norseman 8000
2020-2021 Riot 6000 & 8000
2022 Riot 8000 Early Build
2020-2021 ZR 6000 & 8000
2022 ZR 6000 & 8000 Early Build

Clutching calibration chart can be viewed in the ‘More Info’ tab.
Current list of ADAPT drive clutch calibration components:

1646-005 Spring 85/255 LB
1646-009 Spring 85/225 LB
1646-012 Spring 105/285 LB
1646-015 Spring 105/225 LB
1646-109 Flyweight S2-52
1646-110 Flyweight S2-54
1646-111 Flyweight S2-56
1646-112 Flyweight S2-58
1646-113 Flyweight S2-60
1646-114 Flyweight S2-62
1646-115 Flyweight S2-64
1646-116 Flyweight S2-66
1646-117 Flyweight S2-68
1646-118 Flyweight S2-70